Relubrication: 5 Rules for When and How Much Grease to Apply

Your lubrication route says grease every bearing on the plant floor, once a month, one shot of the grease gun each. It is simple, it is consistent, and it is destroying bearings. Some of those bearings needed grease weeks ago and have been running dry. Others get pumped full every month until the excess blows the seals and cooks them. Same schedule, opposite failures, because the schedule ignores that different bearings need different amounts at different intervals.

Relubrication is not a chore you do the same way to everything. How often and how much grease a bearing needs depends on its size, speed, temperature, and environment, and those vary enormously across a plant. Applying one interval and one quantity to all of them guarantees that most are wrong: over-greased or under-greased, and both kill bearings.

Getting relubrication right is separate from choosing the right grease. You can have the perfect grease and still destroy the bearing by applying it too often, too rarely, or in the wrong amount. Here are the five rules for how often and how much to relubricate your bearings.

Rule 1: The Interval Depends on Speed, Size, and Temperature, Not the Calendar

The biggest relubrication mistake is a fixed calendar interval applied to everything. The correct interval is calculated, and it varies by orders of magnitude across a plant. A small, slow, cool bearing may need relubrication once a year; a large, fast, hot bearing may need it weekly. Greasing them both monthly starves one and floods the other.

The interval depends primarily on speed and bore size (together, the speed factor), and then gets adjusted for temperature, environment, and orientation. Higher speed shortens the interval. Larger bore shortens it. Higher temperature shortens it dramatically, because heat ages grease faster. A vertical shaft or a contaminated environment shortens it further.

The rule: Calculate the relubrication interval for each bearing from its speed, bore size, and temperature, using the bearing manufacturer’s method or chart. Do not apply one calendar interval to a diverse population of bearings. The interval is a calculation, not a convenience.

Rule 2: The Quantity Is Calculated From the Bearing Size, Not Guessed

Just as the interval must be calculated, so must the quantity. There is a standard formula: the relubrication amount in grams is roughly the bearing outside diameter in millimeters times the width in millimeters times a small constant. A large bearing needs many grams; a small one needs a fraction of a gram. Pumping a fixed number of grease-gun shots into every bearing ignores this entirely.

A grease gun delivers a certain amount per stroke (which you should actually measure for your gun, they vary). Knowing the calculated quantity and your gun’s output per stroke tells you how many strokes each bearing needs. This turns greasing from guesswork into a measured amount.

The rule: Calculate the relubrication quantity for each bearing from its dimensions, and know how much your grease gun delivers per stroke, so you apply the correct measured amount. A fixed number of shots for every bearing over-greases the small ones and under-greases the large ones.

Rule 3: Over-Greasing Is as Destructive as Under-Greasing

More grease feels safer, so technicians over-grease, and over-greasing is one of the most common causes of bearing failure. When too much grease is forced into the bearing cavity, it has nowhere to go. The rolling elements churn through the excess, which generates heat, and the grease itself insulates the bearing, trapping that heat. The temperature climbs, the grease degrades, and pressure builds until it blows out the seals, which then lets contamination in.

The signature of over-greasing is a bearing that overheats, with grease purged past the seals, and often seal damage. It is entirely self-inflicted, caused by the well-meaning habit of giving every bearing a generous shot.

The rule: Never over-grease. Apply the calculated quantity, no more. If the bearing has a relief or a way for old grease to escape, use it. The instinct that more grease means more protection is exactly backward past the correct amount. This is one of the specific mechanisms behind lubrication being the leading cause of bearing death, detailed in the number one preventable cause of bearing failure.

Rule 4: Re-Greasing Is Not the Same as Purging Old Grease

Grease does not last forever in a bearing; it ages, oxidizes, and its oil separates out. Simply adding fresh grease on top of old, degraded grease does not fully solve the problem, because the old grease remains, and in some designs it stays packed where fresh grease cannot reach the rolling elements. Over many re-greasing cycles without purging, old hardened grease can accumulate and block fresh grease from doing its job.

This is why bearings with a grease relief or a purge path are designed to let old grease escape as fresh grease is added, cycling the grease rather than just piling it on. And why, periodically, some bearings benefit from being cleaned out and repacked rather than endlessly topped up.

The rule: Where the bearing allows it, let old grease purge as you add fresh, so the grease is renewed, not just accumulated. Understand whether your bearing cycles grease or simply holds it, and for held-grease designs, plan for eventual cleaning and repacking rather than infinite topping up.

Rule 5: Environment and Contamination Shorten Both Interval and Grease Life

The calculated interval and quantity are a starting point that the environment then modifies. A bearing in a hot location needs more frequent, and the grease degrades faster. A bearing in a wet or washdown environment loses grease to water washout and needs more frequent replenishment. A bearing in a contaminated, dusty environment needs more frequent relubrication partly to purge contaminants that have entered, pushing them out with fresh grease.

So two identical bearings, same size and speed, can need very different relubrication schedules if one is in a clean cool room and the other in a hot dirty washdown area. The environment is a multiplier on the base interval.

The rule: Adjust the calculated interval for the environment: shorter for heat, moisture, and contamination. In harsh environments, more frequent relubrication both replaces grease lost or degraded and helps purge contamination. Match the schedule to where the bearing actually lives, and to the grease you selected for those conditions, since interval and grease choice work together, as covered in choosing the right grease for every application.

Turn Greasing From a Chore Into a Program

At IVOR Bearings, we help facilities build relubrication programs with calculated intervals and quantities for each bearing, and we supply the greases and tools to execute them. Contact us at quotes@ivorbearings.com, call +1 305-769-9459, or visit our contact page HERE to build your relubrication program.

The Two Failures a Fixed Schedule Creates

A one-size-fits-all greasing schedule produces two opposite failures at once:

Under-greased bearings running dry: Bearings that needed grease more often than the schedule provides run out, go to metal-to-metal contact, and fail from wear and overheating. Their grease is dry, dark, and depleted.

Over-greased bearings cooked and purged: Bearings that needed less than the schedule provides get overfilled, overheat from churning, and blow their seals. Their grease is purged past the seals and the bearing shows heat damage.

The same monthly-one-shot schedule causes both, on different bearings, at the same time. Neither is a grease-quality problem; both are relubrication-practice problems, and both disappear when interval and quantity are calculated per bearing.

The Financial Impact of Getting Relubrication Right

A facility with 400 grease-lubricated bearings on a single fixed greasing schedule:

With one-size-fits-all greasing:

  • Bearings that are over- or under-greased by the fixed schedule: 50-70%
  • Relubrication-related failures per year: 20-40
  • Average cost per failure including downtime: $3,000-$14,000
  • Annual cost of relubrication-related failures: $60,000-$560,000
  • Wasted grease and labor from over-greasing: additional cost

With calculated intervals and quantities:

  • Each bearing on its correct interval and amount
  • Relubrication-related failures: 3-8 per year
  • Cost to build the program (calculations, route redesign, training): modest, one-time
  • Annual savings: $50,000-$500,000, plus reduced grease waste

The program is a one-time setup that then runs on the correct schedule. The failures from the fixed schedule recur every cycle until the practice is fixed.

Your Action Plan

  1. Stop the one-size-fits-all schedule – Recognize that a single interval and quantity for all bearings is causing both over- and under-greasing simultaneously.
  2. Calculate intervals and quantities per bearing – Use the manufacturer’s method to set the interval from speed, size, and temperature, and the quantity from the bearing dimensions.
  3. Measure your grease gun output – Know how many grams per stroke your gun delivers, so calculated quantities translate into a specific number of strokes.
  4. Adjust for environment and enable grease purging – Shorten intervals for heat, moisture, and contamination, and let old grease cycle out where the design allows.
  5. Partner with lubrication program experts – At IVOR Bearings, we build relubrication programs with per-bearing intervals and quantities, and supply the greases and tools to run them.

We provide: relubrication interval and quantity calculation, greasing route design, grease and tool selection, and technical support to eliminate the over- and under-greasing that a fixed schedule causes.

Our customers stop causing bearing failures with the very maintenance meant to prevent them, by giving each bearing the right amount of grease at the right interval.

The Grease Gun Is Not a Blessing You Sprinkle Evenly

There is a comforting logic to greasing every bearing the same way on the same day: it feels thorough, fair, and simple. But a bearing does not care about fairness; it responds to whether it got the right amount of grease at the right time. Too soon and too much is as fatal as too late and too little, and a uniform schedule delivers both across the plant.

Relubrication done right is a calculation, per bearing, adjusted for where it lives. It is more thought than a fixed route, but it converts greasing from a cause of failure into what it was always supposed to be: the practice that keeps bearings alive. Give each bearing what it actually needs, and the failures you were causing with the grease gun simply stop.

Contact IVOR Bearings today to build your relubrication program. Email us at quotes@ivorbearings.com, call +1 305-769-9459, or visit our contact page HERE to get started.

Right grease, right amount, right interval. Miss any one and the bearing pays.

OTHER POST

5 Mistakes When Setting Tapered Roller Bearing Preload

6 Signs You Have the Wrong Bearing for Your Thrust Load

Relubrication: 5 Rules for When and How Much Grease to Apply